Joint-It Supreme Colour Enhancer™

5-7 YEAR PERFORMANCE*

For paving, paths, roof tiles and walls.

Combined with our Sealer Technology, our Supreme Colour Enhancer™ gives you a performance product that does both jobs professionally.

Available in 5L & 1L

BENEFITS

Ready-to-use

Spray-and-go

Eco-friendly

Quick drying

Breathable

Keeps surface
looking new

Oil & Stain
resistant

Prevents efflorescence

Solvent free &
VOC free

No damage to plants / edible vegetation / tarmac

SURFACE PREPARATION

Remove all surface contamination. Surfaces should be completely dry, clean and free from dust, dirt, oil, efflorescence, organic growth, coatings sealers and old paint films. All algae and mould should be treated and removed prior to application. Cracks in the surface should be repaired before use. Pressure wash up to 2500psi and use of a sterilising solution is advised.

Do not apply in wet, damp conditions or if rain is expected in 4 hours of application

APPLICATION INSTRUCTIONS

Always test a small hidden area before beginning works. DO NOT DILUTE THIS PRODUCT.

Using a low-pressure spray, roller or brush, apply product to the point of saturation. Ensure application is from bottom to top on vertical surfaces. Take care not to let the product run. As the product starts to soak into the substrate, add a second coat, if required. DO NOT ALLOW PRODUCT TO DRY BETWEEN APPLICATIONS. Product will start to work immediately but may take up to 7 days to reach 100% efficacy.

Clean equipment and tools immediately with water after you have finished.

COVERAGE

Coverage depends on the porosity, type and texture of the surface. All surfaces must be treated to saturation in 1-3 applications to ensure 100% efficacy of product. This varies with the substrate, however treating a small hidden area is recommended to calculate true consumption.

General coverage guideline:

Architectural Concrete: 5 SqM/Ltr
Block Paving: 5-8 SqM/Ltr
Porous Natural Stone (Limestone, Sandstone, Slate): 2-5 SqM/Ltr
Low Porosity Stone (Granite, Marble, Terracotta): 8-16 SqM/Ltr

PRECAUTIONS FOR USE

Do not apply Joint-It Supreme Colour Enhancer™ if rain is expected within 4 hours. Product works immediately but it may take up to 7 days to reach 100% efficacy.

Do not apply a second coat if initial coat has dried.

Do not apply during rain or frost or when temperature is below 5℃ or above 30℃.

Wear protective gloves, glasses and appropriate clothing while using Joint-It Supreme Colour Enhancer™.

Keep pets and children away until surface has completely dried.

Keep out of reach of children.

STORAGE

Keep in a dry place between 5ºc and 30ºc in the original container.

Joint-It Supreme Colour Enhancer™ FAQs

Joint-It Supreme Colour Enhancer™ is an eco-friendly, effective combined colour enhancer and sealer for natural stone and concrete surfaces, including paving, paths, roof tiles and walls.

  • Ready-to-use formulation
  • Intensifies Colour
  • Waterproof
  • Stain Resistant
  • Quick Drying
  • Breathable
  • Long lasting
  • Keeps surfaces looking new
  • Eco-Friendly
  • Repels moss and lichen formation on surface

Sealing your surfaces stops dirt and contaminants from penetrating the stone. It prevents weakening of the surface and keeps it looking new. With Joint-It Supreme Colour Enhancer™, you get the added benefit of enhancing the natural colour of the stone also.

Joint-It Supreme Colour Enhancer™ is IN the surface not ON it, and the dirt is ON the stone not IN it. The dirt will never penetrate the stone once Joint-It Supreme Colour Enhancer™ has been applied, but occasionally you may need to clean the top of the stone – this will be much easier because the surface has been treated.

This is not the case. There is no reason to wait for efflorescence to come through. Once you have applied Joint-It Supreme Colour Enhancer™, the water in the sealer pulls the efflorescence out of the stone. When this happens, you can simply brush it off. Now that you have sealed your surface, there is no moisture present to activate the natural salts, and efflorescence should not occur again!

Joint-It Supreme Colour Enhancer ™ can be used immediately after you have finished the jointing process. There is no reason to wait for weeks or months. Our product is completely breathable so the stone can dry during and after the application process.

Coverage depends on the porosity, type and texture of the surface. All surfaces must be treated to saturation in 1-3 applications to ensure 100% efficacy of product. This varies with the substrate, however treating a small hidden area is recommended to calculate true consumption.

Architectural Concrete: 5 SqM/Ltr
Block Paving: 5-8 SqM/Ltr
Porous Natural Stone (Limestone, Sandstone, Slate): 2-5 SqM/Ltr
Low Porosity Stone (Granite, Marble, Terracotta): 8-16 SqM/Ltr

We recommend using Joint-It Supreme Colour Enhancer™ prior to laying paving where you are using Slate, Black/Blue Limestone & Honed Black Granite. These highly porous stones would benefit from being pre-treated to prevent drawing any of the colour of Joint-It Simple™ into the stone.

Joint-It Supreme Colour Enhancer™ Before Use

Remove all surface contamination. Surfaces should be completely dry, clean and free from dust, dirt, oil, efflorescence, organic growth, coatings sealers and old paint films. All algae and mould should be treated and removed prior to application. Cracks in the surface should be repaired before use. Pressure wash up to 2500psi and use of a sterilising solution is advised.

Do not apply in wet, damp conditions or if rain is expected in 4 hours of application.

No. All previous coatings and treatments must be removed prior to using Joint-It Premium Seal™. Due to the nature of sealers, Joint-It Supreme Colour Enhancer™ cannot be absorbed if there is an existing product in the surface.

If you’re not sure if the surface has been treated, pour a steady stream of water onto the surface. If the water absorbs into the surface, there is no sealer present and you can use Joint-It Supreme Colour Enhancer™. If the water forms droplets on the surface, this means the substrate contains a sealer. This must be removed prior to applying Joint-It Supreme Colour Enhancer™.

Do not apply Joint-It Supreme Colour Enhancer™ if rain is expected within 4 hours. Product works immediately but it may take up to 7 days to reach 100% efficacy.

Do not apply a second coat if initial coat has dried.

Do not apply during rain or frost or when temperature is below 5℃ or above 30℃.

Wear protective gloves, glasses and appropriate clothing while using Joint-It Supreme Colour Enhancer™.

Keep pets and children away until surface has completely dried.

Keep out of reach of children.

Substrate Temperature must be between 5℃ and 30℃

Ambient temperature must be between 5℃ and 30℃.

Substrate moisture must be less than 5%.

Yes, we recommend using Joint-It So Clean™ to thoroughly clean your surface before applying Joint-It Supreme Colour Enhancer™. To achieve full penetration into the pores of the surface, dirt and stains need to be removed.

Joint-It Supreme Colour Enhancer™ How To Use

Always test a small hidden area before beginning works. DO NOT DILUTE THIS PRODUCT.

Using a low-pressure spray, roller or brush, apply product to the point of saturation. Ensure application is from bottom to top on vertical surfaces. Take care not to let the product run. As the product starts to soak into the substrate, add a second coat, if required. DO NOT ALLOW PRODUCT TO DRY BETWEEN APPLICATIONS. Product will start to work immediately but may take up to 7 days to reach 100% efficacy.

Clean equipment and tools immediately with water after you have finished.

Joint-It Supreme Colour Enhancer™ When Not To Use

No, Joint-It Supreme Colour Enhancer™ will not work on non-porous surfaces. This product must be absorbed into the substrate to work, and porcelain has almost no absorbency.

No. Joint-It Supreme Colour Enhancer™ cannot be used if rain is expected within 4 hours.

Joint-It Supreme Colour Enhancer™ Storage

Keep in a dry place between 5℃ and 30℃ in the original container.

Immediately after you have finished treating the surface, clean all tools and equipment with water.